How To Paint Slate Fireplace Tiles

Grab a ½” professional stencil brush and dip it into a little bit of your grout line color paint. As long as the surfaces are smooth, the paint will be able to adhere better to your fireplace hearth.

Nicole on Instagram “Slightly obsessed with the new

I placed the stencil material firmly on the mat and taped the sides down for good measure.

How to paint slate fireplace tiles. No matter what type of stone tile you want to paint, it must be clean and free from dust and dirt first. Dip a sponge into the solution, wring most of the liquid out, then wipe the tiles down. Tape off areas you don’t want to accidentally paint.

Scrub the surface with a buffing machine. I didn’t have to paint the entire tile because the slate made a great background color for the stencil. I measured the height of the tile between the top of my fireplace and the bottom of the mantel.

Spray the entire slate by shaking the spray can for a minute or two, then holding it 12 inches or so from the slate. Place the free grout line stencil that comes with your tile stencil over the thin lines in between your stenciled tile. Please remember that preparation is the key to a lasting job and do all of the preparation steps before painting.

What kind of paint should be used to paint fireplace tile? Should be able to get the slate in either 12 x 12, 16 x 16 or a versailles pattern. Despite the challenges during installation, a fireplace hearth creates a beautiful and rustic look.

In my case, this would have been the trim color and i would have painted a little on top of the tape where it meets the tile. Mix a squirt or two of dish soap into a bucket of warm water. Slate tile is porous and will absorb the paint, so it might be necessary to add additional coats of paint to achieve the desired color.

Add a clear coat of polyurethane if desired. This way, if any paint bleeds under the tape, it blends right in. Paint the paint stripper onto the slate's surface with a paint roller and paint brush.

The size tile that is shown in your photo looks to be 12 x 12 or 13 x 13. Again, i have no idea if this is the best product for this job but again it is what i had and what i used. Use a good primer so that your paint will stick.

I painted the first coat with a colored primer for the grout lines, taped off the grout lines with narrow masking tape and then i textured and sponged on a latex paint in a couple of coordinating colors to show texture. How to paint a tile fireplace: I then topped it off with a clearcoat to protect it.

Once i had it in there i measured my fireplace to decide on a size to cut it. Overlap your strokes slightly to avoid missed spots as many sealers have a. Black paint (please read above update):

Paint the granit fireplace surround i mixed up a cup of 7 parts trophy to 2 parts artissimo (both colors from the miss mustard seed’s milk paint line ) and that was a pretty good match to the slate. Also, since it’s exterior paint, i have high hopes it is more heat resistant. All i have left is the grout lines!

Sand tiles to help roughen them up and allow paint to stick better. Paint foam roller set (essential for a smooth, brush stroke free look) sanding blocks; Some say it is not necessary, but i wanted to make sure the paint adhered well.

Let the paint dry for 24 to 48 hours until it is completely dry. Make sure to paint grout as well. Seal the slate first with an impregnating sealer for permanent protection to the stone.

However, if you need to paint your fireplace tile, it’s possible! Begin each spray burst slightly before the edge of the slate, then end it after the slate, overlapping each application of paint row after row. Paint it on with a foam paintbrush, let it penetrate for 10 minutes, then buff it away with a dry cloth.

I would use tricorn black from sherwin williams in matte or some readers have shared the chalk paint has even held up well; I decided on a 9 inch square of a stencil. Can you paint hearth stone?

Use a roller to apply paint evenly to the tile. Brush the sealer onto the surface of each tile using even strokes. Wipe with water and allow to air dry.

I used valspar duramax exterior paint and primer. Seal the paint onto the tiles with a urethane sealer. I made up a mixture of 2 cups of warm water and 1 drop of this dish soapin a small plastic container and wiped down the tile with a cotton cloth and the soap mixture.

Trick for clean paint lines: Whatever paint color is under the tape, use a little bit along the edge on top of the tape. Clean the tile and rinse any soap you used.

It has tips that will help you do a great job. Depending upon your location it may be called another name. After cleaning the tile i gave it a final ‘rinse’ and wiped it down with a slightly wet cloth (with just water, no soap) and let it air dry.

If you're stripping a counter, use a hand buffer with a stripping pad. You don’t need a lot of paint for this part so be careful not to overload your brush. Scrub until the paint residue breaks up and comes off.

I'll show you how i did it in just 3 steps and no sanding! Slate is available in a variety of colors so also is painting a slate fireplace hearth possible which can be painted to match virtually any home decor. Finally, i’m done stenciling tiles.

See more ideas about paint fireplace, fireplace tile, paint fireplace tile.

Image result for slate tile fireplace Slate fireplace